| 1. |
The supply side bonding jumper shall be permitted to be of _______________type or of the wire or bus type.
|
|
|
|
|
|
|
|
|
a)
|
nonflexible metal raceway
|
|
b)
|
flexible metal raceway
|
|
c)
|
nonmetallic raceway
|
|
|
|
|
|
|
| 2. |
The grounded conductor shall not be smaller than the required grounding electrode conductor specified in ____________ but shall not be required to be larger than the largest derived ungrounded conductor(s).
|
|
|
|
|
|
|
|
|
a)
|
Table 250.102
|
|
b)
|
Table 250.66
|
|
|
|
|
|
|
| 3. |
If the source of the separately derived system is located outside the building or structure supplied, a Grounding electrode connection _______________ to one or more grounding electrodes in compliance with 250.50.
|
|
|
|
|
|
|
|
|
a)
|
inside the building
|
|
b)
|
must be made at the first disconnect location
|
|
c)
|
must be made at the source location
|
|
|
|
|
|
|
| 4. |
If a Buildings or Structures Supplied by Separately Derived Grounded System
________________, as described in 250.118, shall be run with the supply conductors and be connected to the building or structure disconnecting means and to the grounding electrode(s).
|
|
|
|
|
|
|
|
|
a)
|
an equipment grounding conductor
|
|
b)
|
a grounding electrode conductor conductor
|
|
c)
|
a bonding conductor
|
|
|
|
|
|
|
| 5. |
An equipment grounding conductor shall not be used as ________________.
|
|
|
|
|
|
|
|
|
a)
|
a grounding electrode
|
|
b)
|
a grounding electrode conductor
|
|
|
|
|
|
|
| 6. |
In general copper ribbons used for equipment grounding conductors in circuits of 1 KV and over are ______________ for solidly grounded systems.
|
|
|
|
|
|
|
|
|
a)
|
insufficient
|
|
b)
|
sufficient
|
|
|
|
|
|
|
| 7. |
Boxes are required to be a minimum of ___________ spacing from corrugated sheet roof decking.
|
|
|
|
|
|
|
|
|
a)
|
˝ inch
|
|
b)
|
1 inch
|
|
c)
|
1 ˝ inch
|
|
|
|
|
|
|
| 8. |
A cable, raceway, or box _________ be installed in concealed locations in metal-corrugated, sheet decking– type roof.
|
|
|
|
|
|
|
|
|
a)
|
are permitted to
|
|
b)
|
shall not
|
|
|
|
|
|
|
| 9. |
__________ expansion/deflection fitting or other approved means shall be used where a raceway crosses a structural joint intended for expansion, contraction or deflection, used in buildings, bridges, parking garages, or other structures.
|
|
|
|
|
|
|
|
|
a)
|
A listed
|
|
b)
|
An approved
|
|
c)
|
An identified
|
|
|
|
|
|
|
| 10. |
_________________________________ are permitted to be installed under a building in concrete, fill, or other masonry without being installed in a raceway.
|
|
|
|
|
|
|
|
|
a)
|
UF cable and USE conductors
|
|
b)
|
Type MC cable listed for direct burial and Type MI cable
|
|
|
|
|
|
|